TLE6212 system-ic for abs/tc/esc product brief, rev. 1, oct. 2008 automotive power
pg-lqfp-64 type package marking TLE6212 pg-lqfp-64 TLE6212 product brief 2 rev. 1, 2008-10-24 system-ic for abs/tc/esc TLE6212 overview features ? quad wheelspeed sensor interface for active sensors ? active wheel speed sensor supply ? active wheel speed signal conditioning ? quad wheelspeed sensor interface for passive sensors ? passive wheel speed signal conditioning ? multi-supply for microcontroller ? control circuit for protected regulator pre-driver (8 v) ? control circuit for three voltage regulators (1.9 v, 3.3 v & 5 v) ? under-and overvoltage reset ? high side driver for pump motor fet ? high side main fet driver ? extended watchdog functionality ? window watchdog ? signature watchdog ? temperature monitoring ? 2 high voltage enable outputs ? 2 high voltage general purpose outputs ? iso conform k-line interface ? 8-bit spi interface ? green product (rohs compliant) ?aec qualified functional description the TLE6212 is a system ic intended for abs, traction control and electronic stability control systems. it is especially designed for automotive use. the device is based on infineon?s power technology spt4 which allows bipolar and cmos control circuitry to be integrated with dmos power devices on the same monolithic circuitry. the TLE6212 includes different functions needed for abs, tc and esc systems as wheel speed sensor interface both for active or passive sensors, multiple supply control for the micro controller and other components on the pcb, high side driver for pump motor and main switch. high voltage enable and general purpose outputs and k-line interface is available for off-board communication. a 8 bit spi interface allows communication and programming from the micro controller. for safety reasons a window watchdog / signature watchdog is included. in addition a logic backbone connects all sub-blocks and its supervision functions to each other and to the spi communication interface.
product brief 3 rev. 1, 2008-10-24 TLE6212 block diagram and pin configuration 1 block diagram and pin configuration 1.1 block diagram figure 1 block diagram TLE6212 supply fet control and monitoring 8v 5v 3.3v 1.9v motor-fet driver main-fet driver standby control internal supply & monitoring timebase charge pump vs monitor and power on overcurrent detection lri lrhs lrls rfi rfhs rfls lfi lfhs lfls ocl u12 u3 u5 g8 uio g5 g3 gnd_reg temperature monitoring temp chp gnd te rri rrhs rrls pdg pdi pds vdg vdbat eni refh refl u7icap refo 8 bit spi reset generator window / signature watchdog high voltage outputs do clk csn di busy resq rst enq2 enq1 wdi gnd1_p wso1 wso2 wsi1 wsi2 k-line (iso9141) interface kline rxd txd wdsel u2 g2 ad 19.08.08 TLE6212_block.vsd apr apf gnd2_p lfo rfo lro rro pdbat high voltage enable output wheelspeed sensor interface for active and passive sensors
edition 2008-10-24 published by infineon technologies ag 81726 munich, germany ? 2008 infineon technologies ag all rights reserved. legal disclaimer the information given in this document shall in no event be regarded as a guarantee of conditions or characteristics. with respect to any examples or hints given herein, any typical values stated herein and/or any information regarding the application of the device, infineon technologies hereby disclaims any and all warranties and liabilities of any kind, including without limitation, warranties of non-infringement of intellectual property rights of any third party. information for further information on technology, delivery terms and conditions and prices, please contact the nearest infineon technologies office ( www.infineon.com ). warnings due to technical requirements, components may contain dangerous substances. for information on the types in question, please contact the nearest infineon technologies office. infineon technologies components may be used in life-support devices or systems only with the express written approval of infineon technologies, if a failure of such components can reasonably be expected to cause the failure of that life-support device or system or to affect the safety or effectiveness of that device or system. life support devices or systems are intended to be implanted in the human body or to support and/or maintain and sustain and/or protect human life. if they fail, it is reasonable to assume that the health of the user or other persons may be endangered.
|
